Space Telescope Science Institute
STIS Instrument Handbook
help@stsci.edu
Table of Contents Previous Next Index Print


Space Telescope Imaging Spectrograph Instrument Handbook for Cycle 22 > Chapter 13: Spectroscopic Reference Material > 13.7 Spectral Purity, Order Confusion, and Peculiarities

13.7
If the PSF had an infinitely small FWHM and no extended wings, a point source would produce a spectrogram with infinitesimal extension in the spatial direction. Furthermore, the spectral resolution would be essentially the theoretical limit of the spectrograph, independent of the entrance slit. In practice, the Optical Telescope Assembly PSF is wider and more complex, and there is scattered light from both the gratings and the detector itself, leading to decreased spectral resolution and spectral purity.
In Figure 13.93 we have plotted Hβ in the white dwarf Feige 110 observed with the G430L grating and five entrance slits with widths between 2˝ and 0.˝05. The spectrum observed through the 0.˝05 and 0.˝1 slits can be considered spectrally pure (remember 0.˝1 maps to 2 pixels on the CCD and 0.˝05 maps to 2 pixels on the MAMAs). Observations with the 0.˝2 slits are still reasonably pure but larger slit widths lead to significant impurity. This becomes evident from the increasing flux in the line core with increasing slit width. The maximum spectral purity is achieved with entrance slits of 0.˝2 width or smaller. Similar results can be seen in Figure 13.94 which shows the calcium triplet regions. Observers wishing to study spectral lines of continuum sources should always consider using small entrance slits.
Figure 13.93: Hβ in the White Dwarf Feige 110 Observed with G430L and 5 Entrance Slits
Figure 13.94: Calcium Triplet Observed with G750L and 7 Entrance Slits
13.7.1 Recommendations for Stellar Observations with Narrow Slits
In assessing the trade between the better spectral purity of small slits and the higher throughput and photometric precision of larger slits, the following should be kept in mind:
1:
2:
Avoid the 52X0.05 slit with the G750 modes, since the Airy core of the point spread function is much larger than the slit size and the resulting light losses may exceed a factor of 5 in comparison with the 52X2 slit. Furthermore, the nominal resolution of 2 pixels is a match to a 0.1 arcsec slit width for the CCD modes.
3:
Longer wavelength observations require wider slits to avoid light loss problems as the point spread function enlarges. Beyond ~5000 , a rapid loss of light is possible even when a 52X0.1 slit is used. In a test of medium dispersion modes, a loss of 10% was found near 4000 , but this increased to 25% by 8500 .
4:
As a stellar target may not be perfectly centered, pipeline fluxes may, in general, be treated as lower limits. Exceptions are the CCD G430Land G750L modes which utilize a Lyot stop.
More complete details on these points can be found in STIS ISR 1998-20 by R. Bohlin and G. Hartig. Regardless of the size of the slit, remember that a peakup will ensure the greatest wavelength accuracy, since an offset of the target in the dispersion direction will be mis-calibrated as an offset of the wavelength scale (see Section 8.1.1 and Section 8.3.1).
13.7.2 Order Overlap and Scattered Light for Echelle Gratings
As with most other echelle spectrographs, STIS echelle data are affected by spectral order overlap at the shortest wavelengths where adjacent spectral orders are not well separated. Echelle observations of continuum sources taken slitless or with a 2X2 entrance slit suffer from severe order overlap. Therefore, an entrance slit of 0.˝2 or smaller height should be used.
Figure 13.95 demonstrates the difference in resolution for a narrow absorption line for BD+75325 observed in the 0.2X0.2 slit vs. a 0.2X0.09 slit. Any difference in the effect of impure light on the depth of the line profiles is less than ~1% of the continuum. An extraction height of 7 pixels is used; and the 0.2X0.09 aperture spectrum is multiplied by 1.28 to compensate for the lower transmission. A slight wavelength shift is maintained to improve visibility.
Figure 13.95: Comparison Between 0.2X0.2 (solid line) and 0.2X0.09 (dotted line) Aperture Spectra of BD+75325 in the E140H-1416 Mode
Note the “oversubtraction” of the black line. This is a ramification of oversubtraction of the background; light which is scattered from the echelle, the OTA PSF, and the detector into the interorder area is being oversubtracted from the science spectrum in the straightforward background subtraction procedure used. The E230M and E230H gratings are only a little affected by this scatter (7% of the light is scattered at ~ 2000 , 4% at 2500 ). However, the E140M and E140H modes do have appreciable scatter; 33% of the light scattered at 1235 for E140M and 15% for E140H; at 1600 this drops to ~12% and 8%, respectively. The STScI provides an ETC, which predicts global and net countrates to sufficient accuracy for planning purposes. An estimate of the net S/N and the net + scattered light in an echelle observation are produced for a specified input spectrum, including an approximation to the scattered component.
An “algorithm” parameter has been added to the x1d spectral extraction task in calstis. Changing this parameter from “unweighted” to sc2d enables a new two-dimensional background subtraction algorithm that was designed by Don Lindler (Sigma Space Corporation) and Chuck Bowers (Goddard Space Flight Center). Alternatively, you can run calstis on the new data with SC2DCORR set to PERFORM in the primary header. (See Section 3.4.20 of the STIS Data Handbook.) Figure 13.96 shows the dramatic improvement achieved with the use of this new algorithm. Figure 13.97 summarizes the fractional error in saturated line cores as a function of wavelength and grating for both algorithms. Errors for the medium resolution gratings are comparable to errors for the high resolution gratings.
Figure 13.96: Comparison between the standard 1-D and the new 2-D background subtraction.
Figure 13.97: Comparison between the errors of the two methods.
Since early 2001, all STIS echelle data obtained from the archive have been processed using the new two-dimensional background subtraction algorithm.
Briefly, the new algorithm works as follows: a 2-D raw image is fit with a 2-D model, reconstructed at each iteration from the best current estimate of the extracted spectrum folded through a semi-empirical simulation of STIS optical properties. Self-consistency between the 2-D model and the extracted spectrum is achieved via iteration. An analogous model containing only scattered light is then constructed using only the echelle scatter outside an 11 pixel wide vertical window centered on each order. This 2-D scattered light model is subtracted from the raw data and the final spectrum is obtained using standard 1-D extraction.
Construction of the 2-D model during each iteration involves several steps. Counts in the 1-D extracted spectrum are mapped back to their idealized origin in hypothetical echelle orders that extend beyond the edge of the physical detector. Echelle scatter is modelled by redistributing extracted counts along diagonal lines of constant wavelength, using echelle line spread functions. Post-echelle smearing along columns is modelled by independently convolving each column with a smoothing kernel. Scattering due to the aperture truncated telescope PSF, isotropic detector halo, and pre-echelle scattering by the cross-disperser are treated by 2-D convolution with a kernel constructed from these components.
13.7.3 Spectroscopic Mode Peculiarities
During the original SMOV and initial observations, a number of first-order mode spectra have been obtained which show additional features which may affect the scientific goals of the observations. One class of spectroscopic images shows diffraction structure of the PSF re-imaged at the various STIS detectors. A second class, commonly referred to as railroad tracks, displays additional “spectra” displaced and parallel to the primary spectrum. Some examples and impacts are presented below.
PSF Re-Imaging
The STIS corrector mirrors re-image the OTA PSF at an intermediate focus within STIS at the location of the slit wheel. This intermediate image is re-imaged to one of the detectors via the selected mode, either imaging or spectroscopic. Any PSF structure present in the slit plane image will be re-imaged at the detectors; however, its appearance in a final spectrum or image depends on the selected mode and the slit or aperture used.
In the imaging modes, little PSF diffraction structure is apparent, since the available filters are typically relatively broad band, smoothing out any structure. The spectroscopic modes, however, create a series of near monochromatic images at the detector plane and the PSF diffraction structure can be detected with the two dimensional STIS detectors.
Point Source: Figure 13.98 shows the spectrum of a point source target, using G140L and slit 52X0.05.
Figure 13.98: Spectrum of a Point Source (Stellar) Target
This typical stellar spectrum (1150–1700 ) shown in panel a, was of a white dwarf for instrument calibration. The Lyman-α absorption feature is apparent near the left end. This image was processed and log stretched to enhance the “fringes” seen above and below the stellar spectrum. These fringes are weak, diverge from the spectrum proportionally to wavelength, and are not present in the Lyman-α gap, indicating they are connected with the source at the slit plane and are not the result of STIS internal scatter. Panel b shows a cross dispersion profile of the original image, cut near the center of the spectrum at about 1430 . The brightest fringe (labelled “1”) is indicated; the peak of the fringe is roughly 0.005 times the peak of the stellar spectrum.
Figure 13.99 illustrates how such fringes are created at the detector. At each wavelength, the portion of the PSF at the slit plane which passes the slit is re-imaged onto the detector. The envelope of all such PSF portions forms the complete image at the detector, as shown. The characteristic fringe separation, proportional to wavelength, is expected as the diffraction structure in the PSF increases with wavelength as shown. In the medium resolution modes, with much less bandpass than the low resolution modes, the tilt of the fringes is much less—they are nearly parallel to the primary spectrum.
Figure 13.99: How Fringes are Created
The fringe visibility is decreased with increasing slit width. Figure 13.99 illustrates this—as the slit broadens, more of a curved portion of the diffraction rings is transmitted. The envelope of these more curved sections is broader with lower contrast compared to the sharp segments visible with a narrow slit.
Out of slit point source: Figure 13.100 shows the spectrum (G140L) of a stellar source, in which the target was mis-located and not nominally in the 52X0.05 slit. While the target center was not located in the slit, the extended PSF structure did cover the slit opening and was transmitted and re-imaged at the detector plane. This image has been processed and log stretched to enhance the faint fringe structure which is apparent.
Figure 13.100: Mis-Located Target—Stellar Source
Figure 13.101 shows a similar case in which the spectrum of a galaxy with a very bright core was obtained with the core located roughly 0.1" from the center of the 0.1" wide slit in the visible mode G750L. The images were processed and log stretched to enhance the fringe appearance. Divergent fringes are apparent above and below the spectrum. A principal component of the “spectrum” consists of changes in the upper and lower portions of the first Airy ring, seen clearly separated at the long wavelength end of the spectrum. (See STIS ISR 2006-02.) These two fringes converge at shorter wavelengths forming a single fringe which overlies the much fainter, off-core portion of the galaxy. The evident blueness of the core spectrum in this particular source makes the combined blue fringes much brighter than the combination of the separated red fringes.
Figure 13.101: Mis-Centered Spectrum of Galaxy with Bright Core
Impact
Diffraction structure in the PSF will set a limit to extracting spectra near a bright source. Blocking the bright source, either by using a coronagraphic aperture or by moving the bright source out of the slit does not remove the inherent, adjacent PSF or diffraction structure. In the case of a faint companion adjacent to a bright, primary source, note that the spectra of the primary and companion will be parallel while the PSF fringes will be tilted. This is especially true in the low resolution modes and may allow the unambiguous identification of a faint companion even in the presence of comparably bright PSF structure.
13.7.4 Railroad Tracks
Figure 13.102 (panel a) shows a processed spectrum of a continuum lamp in mode G750M, λC = 10,363 and slit 0.1X0.2 obtained during ground testing. Beside the spectrum, two adjacent, parallel, secondary spectra are seen symmetrically displaced about 13 pixels from the lamp spectrum. Panel b shows a cross dispersion profile illustrating the magnitude and shape of the spectra. The secondary spectra have peak intensities about 8% of the primary spectrum but are broader and asymmetric. This was the only example of this peculiar condition noticed during ground testing; however, subsequent review showed one additional example also obtained during ground testing. This second case was a similar continuum lamp spectrum using G750M, λC = 7795, with the same slit. Secondary spectra were ~8% and 3% (peak intensity) of the primary peak intensity.
Figure 13.102: Railroad Tracks
One similar example has been obtained in flight to date, with the UV mode G230LB and the CCD. The target was a very red star. The parallel, secondary spectra are visible at a level of about 8% of peak intensity.
The cause of these secondary spectra in these three observations is not known. The three cases observed have all been with the CCD; no MAMA examples have been obtained. Other observations in these modes under similar conditions have not shown such effects. In all cases, a red source was observed. The broad profile and relatively bright intensity of the secondary spectra suggest a multiple reflection instead of a diffraction origin, but no way of producing dual, symmetric features has yet been proposed which is consistent with these observations.

Space Telescope Imaging Spectrograph Instrument Handbook for Cycle 22 > Chapter 13: Spectroscopic Reference Material > 13.7 Spectral Purity, Order Confusion, and Peculiarities

Table of Contents Previous Next Index Print