12795( 8) - 28-Feb-2012 19:03:26 - [ 1] HUBBLE SPACE TELESCOPE OBSERVING PROGRAM 12795 Version: 8 Check-in Time: 28-Feb-2012 19:03:26 STScI Edit Number: 2 Title Second COS FUV Lifetime Position: Verification of Aperture and FUV Spectrum Placement (FENA2) ------------------------------------------------------------------------------------ Type Cycle CAL/COS 19 ------------------------------------------------------------------------------------ Investigators Contact? PI: Dr. Charles R. Proffitt Computer Sciences Corporation CoI: Dr. Steven V. Penton University of Colorado at Boulder N CoI: Dr. David J. Sahnow Space Telescope Science Institute N ------------------------------------------------------------------------------------ Abstract This proposal will determine the exact spacecraft pointing offset and the aperture offsets needed for the 2nd COS FUV lifetime position. The intent is to shift COS FUV spectra up by 35 pixels on the detector to avoid the heavily gain sagged region around the current position. ------------------------------------------------------------------------------------ Observations Description ------------------------ Visit 1 will take spectra with all three gratings at our best estimate for the new lifetime position (2.94" or +35 pixels) and at 3.78" (+45 pixels). This will verify how the spectra fall relative to the measured gain map on the detector and given an initial estimate of the offsets and plate scales needed for target acquisitions at the new lifetime position. Visit 2 will place a G130M 1291 spectrum at athe new lifetime position and take repeated exposures while sweeping the PSA aperture across the target to verify the aperture throughput vs positional offset. G130M and G160M exposures will use 36 s lamp flashes to provide extra signal in the wavecal spectra while G140L exposures will use a flash of 21 s. However, in visit 2, all exposures with nozero YAPER values (i.e., moving the aperture block in the dispersion direction), will set the lamp current to low and take two 8 s lamp flashes with 20 s separation between the start times. This is done because it has never been verified if a lamp light leak might open up with a large enough move in the dispersion direction. Offsets for visit 2 were updated based on visit 1 results to use +3.5" and -73 motor steps as the estimates for the new position. Real Time Justification ----------------------- Calibration Justification ------------------------- Additional Comments ------------------- For visits 01 & 02, do not allow any FUV transitions out of HVNOM within each visit (except for between the last two exps). This is automatically enforced 12795( 8) - 28-Feb-2012 19:03:26 - [ 2] via exposure level AFTER BYs and SEQ NON-INTs to prevent exposures from separating enough to cause the transition but should be verified. It also forces SAA FREE scheduling only. SQL is required in order to 1. Id S/C exposures as COS. 2. Bypass calibration for the G140L exposures of V01. 3. Bypass calibration for odd numbered exposures 31-41 and 45-55 of V02. Note that the odd numbered exposures in this range are mech moves and don't get calibrated in any case. Exposures 43 and 57 should be calibrated, as should all science exposures up to and including expo 29. ------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 3] TARGET LIST Fixed Targets ------------------------------------------------------------------------------------------------------------------------------------ Tar| Target | Target | Target |Coord | Radial | Flux data No | Name | Description | Position |Eqnx | Vel. | ------------------------------------------------------------------------------------------------------------------------------------ 3 WD0308-565 STAR, DB RA=03H09M47.9200S +/- 0.1", J2000 V = -68 V = 14.07 +/- 0.02 DEC=-56D23'49.41" +/- 0.1" Reference Frame: ICRS Comments: Position and proper motions from the Third U.S. Naval Observatory CCD Astrograph Catalog (UCAC3) Zacharias et al. 2009 Epoch of Position RA proper motion (seconds of time/yr) DEC Proper Motion (arcsec/yr) Annual Parallax (arcsec) 2000 0.01814126767953136 0.0643 0.0 ------------------------------------------------------------------------------------------------------------------------------------ 2 WD0947+857 STAR, DA RA=09H57M54.4230S +/- 0.1", J2000 V = 15.9 DEC=+85D29'40.91" +/- 0.1" Reference Frame: ICRS Comments: HST FASTEX standard PM, coords from GSC2 From UCAC3 get coords 09 57 54.308 +85 29 40.84 pm -23.4, -9.8 mas/yr - double entry! Epoch of Position RA proper motion (seconds of time/yr) DEC Proper Motion (arcsec/yr) Annual Parallax (arcsec) 1997.19 -0.01747 -0.0253 0.0 ------------------------------------------------------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 4] Visit: 01 Visit Requirements: SCHED 100%; BETWEEN 20-FEB-2012:00:00:00 AND 27-FEB-2012:00:00:00 On Hold Comments: Additional Comments: Change FUV HVB level to 167 to avoid divot and clod. Set HVA to 169. Acquire target with an NUV BOA ACQ/IMAGE. Then take a 54 s G130M 1291 exposure at the current position. Adopt plate scale of 11.9 pixels/arc-sec and block scale of -21 steps/arc-sec Next move the aperture block to XAPER = -62 or +2.94", and take a 54 s G130M 1291 + 163 s G160M 1600 + 40 s G140L 1280 exposures. Finally, move the aperture block to XAPER = -79 or +3.78" and repeat the above exposure sequence. All exposures to be done using ~3X normal flash times. Reset HVB level to standard. Disallow FUV transitions out of HVNOM within the visit (exp AFTERs and SEQ NON-INTs should enforce this). Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 450 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; GS ACQ SCENARIO BASE1B3; QASISTATES COS FUV HVLOW HVNOM; QESIPARM ENDCTSB 167; QESIPARM ENDCTSA 169 Comments: SQL required for qexposure to specify the si_used = "COS" The overhead on this exposure can actually be hidden under the guide star exposure and the previous occultation, but this is not reflected by APT and so the visits do not appear to fit within the allocated orbits. The following exposure (the ACQ) needs to have an exposure-level AFTER of 1 to 900 seconds. This will prevent SPSS to separating these two exposures by too large a gap, which if large enough, would reset the HV back to the default value. ------------------------------------------------------------------------------------------------------------------------------------ 2 WD0308-565 COS/NUV ACQ/IMA BOA MIRRORA 1 42.0 S AFTER BY 0 S TO 900 S; GE SEQ 2-11 NON-INT Comments: SN=60 in 42 seconds, brightest pixel=11.95 c/p/s; global rate 925, COS.ta.348879 ------------------------------------------------------------------------------------------------------------------------------------ 3 WD0308-565 COS/FUV TIME-TA PSA G130M 1291 BUFFER-TIME=186, FP-POS=3, 1 54 S G FLASH=S0200D036 Comments: Observation at standard position to verify location and provide WCA location 12795( 8) - 28-Feb-2012 19:03:26 - [ 5] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 4 NONE COS ALIGN/A XAPER=-62, YAPER=0 1 0.0 S PER Comments: Assume 21 motor steps/" ------------------------------------------------------------------------------------------------------------------------------------ 5 WD0308-565 COS/FUV TIME-TA PSA G130M 1291 BUFFER-TIME=186, FP-POS=3, 1 54 S POS TARG 0, 2.94; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer ------------------------------------------------------------------------------------------------------------------------------------ 6 WD0308-565 COS/FUV TIME-TA PSA G160M 1600 BUFFER-TIME=377, FP-POS=3, 1 163 S POS TARG 0, 2.94; SPEC G FLASH=S0120D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer ------------------------------------------------------------------------------------------------------------------------------------ 7 WD0308-565 COS/FUV TIME-TA PSA G140L 1280 BUFFER-TIME=263, FP-POS=3, 1 40 S POS TARG 0, 2.94; SPEC G FLASH=S0200D021 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer. SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 8 NONE COS ALIGN/A XAPER=-79, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 9 WD0308-565 COS/FUV TIME-TA PSA G130M 1291 BUFFER-TIME=186, FP-POS=3, 1 54 S POS TARG 0, 3.78; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer ------------------------------------------------------------------------------------------------------------------------------------ 10 WD0308-565 COS/FUV TIME-TA PSA G160M 1600 BUFFER-TIME=377, FP-POS=3, 1 163 S POS TARG 0, 3.78; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer ------------------------------------------------------------------------------------------------------------------------------------ 11 WD0308-565 COS/FUV TIME-TA PSA G140L 1280 BUFFER-TIME=263, FP-POS=3, 1 40 S POS TARG 0, 3.78; SPEC G FLASH=S0200D021 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer. SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 6] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 12 DARK S/C DATA NONE 1 1 S NEW OBSET; QASISTATES COS FUV HVLOW HVLOW; QASISTATES COS SI OBSERVE OBSERVE Comments: SQL required for qexposure to specify the si_used = "COS" New obset SR necessary to force this exposure to be the very last exposure after Home. ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A WD0308-565 2 COS/NUV ACQ/IMA BOA MIRRORA none none none none 1 N/A GE WD0308-565 3 COS/FUV TIME-TA PSA G130M 1291 none none none none 1 N/A G NONE 4 COS ALIGN/A none none none none 2 N/A PER WD0308-565 5 COS/FUV TIME-TA PSA G130M 1291 none none none none 2 N/A G WD0308-565 6 COS/FUV TIME-TA PSA G160M 1600 none none none none 2 N/A G WD0308-565 7 COS/FUV TIME-TA PSA G140L 1280 none none none none 2 N/A G NONE 8 COS ALIGN/A none none none none 2 N/A PER WD0308-565 9 COS/FUV TIME-TA PSA G130M 1291 none none none none 2 N/A G WD0308-565 10 COS/FUV TIME-TA PSA G160M 1600 none none none none 2 N/A G WD0308-565 11 COS/FUV TIME-TA PSA G140L 1280 none none none none 2 N/A G DARK 12 S/C DATA NONE none none none none 3 N/A 12795( 8) - 28-Feb-2012 19:03:26 - [ 7] Visit: 02 Visit Requirements: SCHED 100%; BETWEEN 12-MAR-2012:00:00:00 AND 19-MAR-2012:00:00:00 On Hold Comments: Additional Comments: This version includes resetting the segment B HV to 167 and segment A to 169 Updated offsets based on visit 1 results Change to +35 arc-sec and -73 motor steps based on visit 1 results Adopt pattern of aperture motions in motor steps relative to new center of -29 -23 -18 -14 -10 -6 0 6 10 14 18 23 29 equivalent shift in arc-sec for these motions is -1.38 -1.10 -0.86 -0.67 -0.48 -0.29 0.00 0.29 0.48 0.67 0.86 1.10 1.38 Adding in the -73 motor step offset from the current position, the needed XAPER values become -102 -96 -91 -87 -83 -79 -73 -67 -63 -59 -55 -50 -44 For exposures offset from nominal in the dispersion direction use CURRENT=LOW and FLASH=S0020D008 to allow for unexpected light leak. Disallow FUV transitions out of HVNOM within the visit (exp AFTERs and SEQ NON-INTs should enforce this). Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 450 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; QASISTATES COS FUV HVLOW HVNOM; QESIPARM ENDCTSB 167; QESIPARM ENDCTSA 169 Comments: SQL required for qexposure to specify the si_used = "COS" The overhead on this exposure can actually be hidden under the guide star exposure and the previous occultation, but this is not reflected by APT and so the visits do not appear to fit within the allocated orbits. The following exposure (the ACQ) needs to have an exposure-level AFTER of 1 to 900 seconds. This will prevent SPSS to separating these two exposures by too large a gap, which if large enough, would reset the HV back to the default value. ------------------------------------------------------------------------------------------------------------------------------------ 2 WD0947+857 COS/NUV ACQ/IMA BOA MIRRORA 1 85.0 S AFTER BY 0 S TO 900 S; GE SEQ 2-27 NON-INT Comments: SN=60 in 85 seconds, brightest pixel=5.9 cts/s (COS.A217972) ------------------------------------------------------------------------------------------------------------------------------------ 3 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=200, FP-POS=3 1 25 S G 12795( 8) - 28-Feb-2012 19:03:26 - [ 8] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 4 NONE COS ALIGN/A XAPER=-102, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 5 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 6 NONE COS ALIGN/A XAPER=-96, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 7 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 8 NONE COS ALIGN/A XAPER=-91, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 9 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 10 NONE COS ALIGN/A XAPER=-87, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 11 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 12 NONE COS ALIGN/A XAPER=-83, YAPER=0 1 0.0 S PER 12795( 8) - 28-Feb-2012 19:03:26 - [ 9] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 13 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 14 NONE COS ALIGN/A XAPER=-79, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 15 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 16 NONE COS ALIGN/A XAPER=-73, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 17 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 18 NONE COS ALIGN/A XAPER=-67, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 19 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 20 NONE COS ALIGN/A XAPER=-63, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 10] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 21 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 22 NONE COS ALIGN/A XAPER=-59, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 23 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 24 NONE COS ALIGN/A XAPER=-55, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 25 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 26 NONE COS ALIGN/A XAPER=-50, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 27 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 28 NONE COS ALIGN/A XAPER=-44, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 11] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 29 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN; SEQ 29-57 NON-INT Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 30 NONE COS ALIGN/A XAPER=-73, YAPER=29 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 31 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 32 NONE COS ALIGN/A XAPER=-73, YAPER=23 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 33 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 34 NONE COS ALIGN/A XAPER=-73, YAPER=18 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 35 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. 12795( 8) - 28-Feb-2012 19:03:26 - [ 12] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 36 NONE COS ALIGN/A XAPER=-73, YAPER=14 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 37 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 38 NONE COS ALIGN/A XAPER=-73, YAPER=10 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 39 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 40 NONE COS ALIGN/A XAPER=-73, YAPER=6 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 41 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 42 NONE COS ALIGN/A XAPER=-73, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 13] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 43 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position ------------------------------------------------------------------------------------------------------------------------------------ 44 NONE COS ALIGN/A XAPER=-73, YAPER=-6 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 45 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 46 NONE COS ALIGN/A XAPER=-73, YAPER=-10 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 47 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 48 NONE COS ALIGN/A XAPER=-73, YAPER=-14 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 49 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 12795( 8) - 28-Feb-2012 19:03:26 - [ 14] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 50 NONE COS ALIGN/A XAPER=-73, YAPER=-18 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 51 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 52 NONE COS ALIGN/A XAPER=-73, YAPER=-23 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 53 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 54 NONE COS ALIGN/A XAPER=-73, YAPER=-29 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 55 WD0947+857 COS/FUV TIME-TA PSA G130M 1309 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG 0, 3.5; SPEC G CURRENT=LOW, FLASH=S0020D008 COM INSTR ELNOAPMAIN; QESIPARM USELAMP LINE2 Comments: Set BUFFER-TIME > EXPO-TIME to only dump used part of buffer Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position SQL required to bypass calibration. ------------------------------------------------------------------------------------------------------------------------------------ 56 NONE COS ALIGN/A XAPER=-73, YAPER=0 1 0.0 S PER ------------------------------------------------------------------------------------------------------------------------------------ 57 WD0947+857 COS/FUV TIME-TA PSA G160M 1600 BUFFER-TIME=174, FP-POS=3, 1 50.0 S POS TARG null, 3.5; SPEC G FLASH=S0200D036 COM INSTR ELNOAPMAIN Comments: Special requirement ELNOAPMAIN needed to ensure aperture does not move to default position 12795( 8) - 28-Feb-2012 19:03:26 - [ 15] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 58 DARK S/C DATA NONE 1 1 S NEW OBSET; QASISTATES COS FUV HVLOW HVLOW; QASISTATES COS SI OBSERVE OBSERVE Comments: SQL required for qexposure to specify the si_used = "COS" New obset SR necessary to force this exposure to be the very last exposure after Home. ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A WD0947+857 2 COS/NUV ACQ/IMA BOA MIRRORA none none none none 2 N/A GE WD0947+857 3 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 4 COS ALIGN/A none none none none 2 N/A PER WD0947+857 5 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 6 COS ALIGN/A none none none none 2 N/A PER WD0947+857 7 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 8 COS ALIGN/A none none none none 2 N/A PER WD0947+857 9 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 10 COS ALIGN/A none none none none 2 N/A PER WD0947+857 11 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 12 COS ALIGN/A none none none none 2 N/A PER WD0947+857 13 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 14 COS ALIGN/A none none none none 2 N/A PER WD0947+857 15 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G 12795( 8) - 28-Feb-2012 19:03:26 - [ 16] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ NONE 16 COS ALIGN/A none none none none 2 N/A PER WD0947+857 17 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 18 COS ALIGN/A none none none none 2 N/A PER WD0947+857 19 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 20 COS ALIGN/A none none none none 2 N/A PER WD0947+857 21 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 22 COS ALIGN/A none none none none 2 N/A PER WD0947+857 23 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 24 COS ALIGN/A none none none none 2 N/A PER WD0947+857 25 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 26 COS ALIGN/A none none none none 2 N/A PER WD0947+857 27 COS/FUV TIME-TA PSA G130M 1309 none none none none 2 N/A G NONE 28 COS ALIGN/A none none none none 2 N/A PER WD0947+857 29 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 30 COS ALIGN/A none none none none 3 N/A PER WD0947+857 31 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 32 COS ALIGN/A none none none none 3 N/A PER WD0947+857 33 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 34 COS ALIGN/A none none none none 3 N/A PER WD0947+857 35 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 36 COS ALIGN/A none none none none 3 N/A PER WD0947+857 37 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 38 COS ALIGN/A none none none none 3 N/A PER WD0947+857 39 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G 12795( 8) - 28-Feb-2012 19:03:26 - [ 17] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ NONE 40 COS ALIGN/A none none none none 3 N/A PER WD0947+857 41 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 42 COS ALIGN/A none none none none 3 N/A PER WD0947+857 43 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 44 COS ALIGN/A none none none none 3 N/A PER WD0947+857 45 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 46 COS ALIGN/A none none none none 3 N/A PER WD0947+857 47 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 48 COS ALIGN/A none none none none 3 N/A PER WD0947+857 49 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 50 COS ALIGN/A none none none none 3 N/A PER WD0947+857 51 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 52 COS ALIGN/A none none none none 3 N/A PER WD0947+857 53 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 54 COS ALIGN/A none none none none 3 N/A PER WD0947+857 55 COS/FUV TIME-TA PSA G130M 1309 none none none none 3 N/A G NONE 56 COS ALIGN/A none none none none 3 N/A PER WD0947+857 57 COS/FUV TIME-TA PSA G160M 1600 none none none none 3 N/A G DARK 58 S/C DATA NONE none none none none 4 N/A 12795( 8) - 28-Feb-2012 19:03:26 - [ 18] Summary Form for Proposal 12795 Item Used in this proposal ------------------------------------------------------------------------------------------------------------------------------------ Apertures BOA, NONE, PSA ------------------------------------------------------------------------------------------------------------------------------------ Configurations COS, COS/FUV, COS/NUV, S/C ------------------------------------------------------------------------------------------------------------------------------------ Opmodes ACQ/IMAGE, ALIGN/APER, DATA, TIME-TAG ------------------------------------------------------------------------------------------------------------------------------------ Optional Parameters BUFFER-TIME=174, BUFFER-TIME=186, BUFFER-TIME=200, BUFFER-TIME=263, BUFFER-TIME=377, CURRENT=LOW, FLASH=S0020D008, FLASH=S0120D036, FLASH=S0200D021, FLASH=S0200D036, FP-POS=3, XAPER=-102, XAPER=-44, XAPER=-50, XAPER=-55, XAPER=-59, XAPER=-62, XAPER=-63, XAPER=-67, XAPER=-73, XAPER=-79, XAPER=-83, XAPER=-87, XAPER=-91, XAPER=-96, YAPER=-10, YAPER=-14, YAPER=-18, YAPER=-23, YAPER=-29, YAPER=-6, YAPER=0, YAPER=10, YAPER=14, YAPER=18, YAPER=23, YAPER=29, YAPER=6 ------------------------------------------------------------------------------------------------------------------------------------ Special Requirements AFTER BY 0 S TO 900 S, BETWEEN 12-MAR-2012:00:00:00 AND 19-MAR-2012:00:00:00, BETWEEN 20-FEB-2012:00:00:00 AND 27-FEB-2012:00:00:00, GS ACQ SCENARIO BASE1B3, NEW OBSET, POS TARG 0, 2.94, POS TARG 0, 3.5, POS TARG 0, 3.78, POS TARG null, 3.5, QASISTATES COS FUV HVLOW HVLOW, QASISTATES COS FUV HVLOW HVNOM, QASISTATES COS SI OBSERVE OBSERVE, QESIPARM ENDCTSA 169, QESIPARM ENDCTSB 167, QESIPARM USELAMP LINE2, SAA CONTOUR 31, SCHED 100%, SEQ 2-11 NON-INT, SEQ 2-27 NON-INT, SEQ 29-57 NON-INT, SPEC COM INSTR ELHLTHVF, SPEC COM INSTR ELNOAPMAIN ------------------------------------------------------------------------------------------------------------------------------------ Spectral Elements G130M, G140L, G160M, MIRRORA ------------------------------------------------------------------------------------------------------------------------------------ Target Names DARK, NONE, WD0308-565, WD0947+857 ------------------------------------------------------------------------------------------------------------------------------------