12810( 8) - 14-May-2012 18:01:43 - [ 1] HUBBLE SPACE TELESCOPE OBSERVING PROGRAM 12810 Version: 8 Check-in Time: 14-May-2012 18:01:43 STScI Edit Number: 5 Title COS/FUV Special Recovery ------------------------------------------------------------------------------------ Type Cycle ENG/COS 19 ------------------------------------------------------------------------------------ Investigators Contact? PI: Mr. Thomas Wheeler Space Telescope Science Institute CoI: Dr. Alan D. Welty Space Telescope Science Institute N CoI: Dr. David J. Sahnow Space Telescope Science Institute N CoI: Dr. Charles R. Proffitt Computer Sciences Corporation N CoI: Dr. Steven V. Penton Space Telescope Science Institute N ------------------------------------------------------------------------------------ Abstract This proposal consists of the steps necessary for turning on and ramping up (in magnitude) the COS FUV high voltage and returning the FUV detector to science operations in a conservative manner after a HV anomalous or burst event (similar to what has been seen on FUSE) shutdown. HSTAR 13305 provides details and timeline of the present shutdown. The complete step-by-step procedure is detailed in the Observing Description, but in summary, the following is done: Groups of sequences with one day’s activities with the QE grid off and one day’s activities with the QE grid on alternate to progressively higher voltages with the QE off group leading by one sequence. The initial HV turn on (Day 1) occurs with the QE grid off; the initial transition from FUV Operate to HVLow is broken into two parts with a 1- hour wait between turning the HV on and ramping to HVLow (SAA). The next Day 1 visit is 1 hour later, where the HV is turned off by returning the FUV Operate state. After another1-hour wait, the QE grid is turned on, the HV is turned on and the voltage is not ramped. After another 1-hour wait, the HV is turned off returning to FUV Operate. The Day 1 ends with the NSSC-1 COS flag 3 is set to prevent any FUV HV commanding. This is followed by 10 cycles (2 * 5 cycles - one set of cycles with the grid off and one set with the grid on) of HV ramp-ups and returns to FUV Operate (HV off) alternating between grid off and on with the QE off group leading by one HV setting. The HV Commanded Counts for each group of cycles are: 154/151, 160/157, 166/163, 172/169, HVNom (178/175). (The formula to convert Command Counts to HV is: Volts = (Command Counts * -15.69V) -2500V.) The QE off and QE on cycles are similar except for the QE commanding. One typical QE off cycle is shown below: V14 QE off - Ramp to 166/163 After V10 by 2D for analysis. Flag 3 must be cleared to execute. 1. QE off - Turn HV on 2. Ramp to HVLow (100/100) 3. Ramp HV to 166/163 4. DCE RAM dump 5. Dark exposure 6. Wave exposure 12810( 8) - 14-May-2012 18:01:43 - [ 2] V15 Return to Operate After V14 by 1hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM Dump 6. Set flag 3 In some later cycles with the QE grid on, ground system QasiStates are used to auto-schedule the Operate to HVNom transition. Visits 21 and 25 are going to HVNom (178/175) with the QE grid off and on, respectively. There will be a gap of 2days between grid-off cycles and 2 days between grid-on cycles, offset by 1 day. (See the proposal description for exact timing.) All HV ramp-up will be done at the nominal value of 3 seconds per HV "step" rather than 10 seconds per HV "step" used in SMOV. The concern during SMOV was that gas exposure during launch would allow gas to adsorb on the MCP pore surfaces, and that slower ramping would help to remove this excess gas. This concern no longer exists. The cycle voltage values (for Segments A and B) must be patched in FSW in each cycle prior to the HV ramp commanding. Memory monitors will be set on the patched memory locations. Immediately after obtaining the commanded voltage for that cycle and after return to FUV Operate (HV-off) commanding, the DCE memory will be dumped. After HV ramp-up commanding starting with HVLow and prior to returning to HV off, short DARK exposures (300 secs.) with Stim Rate = 2000 will be obtained and after HV ramp-up commanding starting with levels above HVLow and prior to returning to HV off, short WAVE exposures (60 secs.) will be obtained. After all visits that end with Return to Operate (HV off), NSSC-1 COS event flag 3 will be set to inhibit any FUV commanding, a.k.a. a “dead man’s” switch. If the flag remains set, subsequent FUV commanding will be skipped. Thus, Operations Requests must be in place to clear the flag prior to those subsequent visits. Real-time monitoring of the telemetry will be used to guide the decisions whether or not to clear the flag. This is also required after the final visit. Throughout the proposal, different “after by” times, sequence containers, and new alignments are used to optimize flow, schedulability, telemetry and science data analyses, and the clearing of flag 3. The proposal is designed such that the visits and exposures MUST be executed in order. Additionally, all visits are compliant with CARD 3.4.12.8 - COS FUV Mandatory Dwell Time at HVLow (1 hour dwell at HVLow before ramping to a more negative voltage) and CARD 3.4.12.9 – COS FUV High Voltage QE Grid Operation (HV must be less negative or equal to the HVLow to switch grid on or off). ------------------------------------------------------------------------------------ Observations Description ------------------------ This proposal consists of necessary steps for turning on and ramping up the COS FUV high voltage in a conservative manner after an anomalous or "burst" shutdown. It is intended to be used for the on-orbit turn-on of the detector after such a shutdown. The sequence day, visits numbers, exposures, and rough “after by” times (end to start) are listed. Number listed as in parentheses, e.g., (100/100) or 154/151 are the HV command counts for Segment A and B, 12810( 8) - 14-May-2012 18:01:43 - [ 3] respectively. Proposal 12810 FUV Recovery Sequence – Version 11 Day 1 V01 QE off - Turn HV on -- Flag 3 must be clear to execute. 1. QE off - Turn HV on (0/0 do not ramp) 2. DCE RAM dump V02 QE off - Ramp to HVLow -- After V01 by 1.1hr to 10.0hr 1. Ramp to HVLow (100/100) 2. DCE RAM dump 3. Dark exposure V03 Return to Operate -- After V02 by 1.5hr to 10.0hr 1. Return to Operate (HV off) 2. DCE RAM dump V04 QE on - Turn HV on -- After V03 by 1.1hr to 10.0hr 1. QE on - Turn HV on (0/0 do not ramp) 2. DCE RAM dump V05 Return to Operate -- After V04 by 1.1hr to 10.0hr 1. Return to Operte (HV off) 2. DCE RAM dump 3. Set flag 3 Day 2 V06 QE off - Ramp HV to 154/151 -- After V01 by 1D to 2D for analysis. Flag 3 must be clear to execute. 1. Install memory monitors 2. QE off - Turn HV on (0/0) 3. Ramp to HVLow (100/100) 4. Ramp to 154/151 5. DCE RAM dump 6. Dark exposure 7. Wave exposure V07 Return to Operate -- After V06 by 2.8hr to 3.2hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 3 V08 QE on - Ramp to HVLow (100/100) -- After V04 by 2D to 4D for analysis. Flag 3 must be clear to execute. 1. QE on - Turn HV on (0/0) - Ramp to HVLow (100/100) 2. DCE RAM Dump 3. Dark exposure V09 Return to Operate -- After V08 by 1.6hr to 10.0hr 1. Return to Operate (HV off) 2. DCE RAM dump 3. Set flag 3 Day 4 V10 QE off - Ramp HV to 160/157 -- After V06 by 2D to 4D for analysis. Flag 3 must be clear to execute. 1. QE off – Turn HV 12810( 8) - 14-May-2012 18:01:43 - [ 4] 2. Ramp to HVLow (100/100) 3. Ramp to 160/157 4. DCE RAM dump 5. Dark exposure 6. Wave exposure V11 Return to Operate -- After V10 by 2.8hr to 3.2 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 5 V12 QE on - Ramp to 154/151 -- After V08 by 2D to 4D for analysis. Flag 3 must be clear to execute. Qasi_States will auto-schedule the normal Operate to HVLow transition 1. Ramp HV to 154/151 2. DCE RAM dump 3. Dark exposure 4. Wave exposure V13 Return to Operate -- After V12 by 1.5hr to 2.1hrs 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 6 V14 QE off - Ramp to 166/163 -- After V10 by 2D to 4D for analysis. Flag 3 must be clear to execute. 1. QE off - Turn HV on 2. Ramp to HVLow (100/100) 3. Ramp HV to 166/163 4. DCE RAM dump 5. Dark exposure 6. Wave exposure V15 Return to Operate -- After V14 by 2.8hr to 3.4hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM Dump 6. Set flag 3 Day 7 V16 QE on - Ramp to 160/157 -- After V12 by 2D to 4D for analysis. Flag 3 must be clear to execute. Qasi_States will auto-schedule the normal Operate to HVLow transition 1. Ramp HV to 160/157 2. DCE RAM dump 3. Dark exposure 4. Wave exposure V17 Return to Operate -- After V16 by 1.5hr to 2.1hr 1. Dark exposure 12810( 8) - 14-May-2012 18:01:43 - [ 5] 2. Wave exposure 3. Return to HVLow 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 8 V18 QE off - Ramp to 172/169 -- After V14 by 2D to 4D for analysis. Flag 3 must be clear to execute. 1. QE off - Turn HV on 2. Ramp to HVLow (100/100) 3. Ramp HV to 172/169 4. DCE RAM Dump 5. Dark exposure 6. Wave exposure V19 Return to Operate -- After V18 by 2.8hr to 3.4hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 9 V20 QE on - Ramp to 166/163 -- After V16 by 2D to 4D for analysis. Flag 3 must be clear to execute. Qasi_States will auto-schedule the normal Operate to HVLow transition 1. Ramp to HV to 166/163 2. DCE RAM dump 3. Dark exposure 4. Wave exposure V21 Return to Operate -- After by V20 by 1.6hr to 2.1hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 10 V22 QE off - Ramp to HVNom (178/175) -- After V18 by 2D to 4D for analysis. Flag 3 must be clear to execute. 1. QE off - Turn HV on 2. Ramp to HVLow (100/100) 3. Ramp HV to HVNom (178/175) 4. DCE RAM dump 5. Dark exposure 6. Wave exposure V23 Return to Operate -- After V22 by 2.8hr to 3.4hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to HV Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 11 12810( 8) - 14-May-2012 18:01:43 - [ 6] V24 QE on - Ramp to 172/169 -- After V20 by 2D to 4D for analysis. Flag 3 must be clear to execute. Qasi_States will auto-schedule the normal Operate to HVLow transition 1. Ramp to HV to 172/169 2. DCE RAM dump 3. Dark exposure 4. Wave exposure V25 Return to Operate -- After V24 by 1.5hr to 2.1hr 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 12 V26 QE on - Ramp to HVNom (178/175) -- After V24 by 1D to 2D for analysis. Flag 3 must be clear to execute. Qasi_States will auto-schedule the normal Operate to HVLow transition 1. Ramp to HV to HVNom (178/175) 2. DCE RAM dump 3. Dark exposure 4. Wave exposure V27 Return to HVOperate -- After V26 by 1.5hr to 2.1 1. Dark exposure 2. Wave exposure 3. Return to HVLow (100/100) 4. Return to Operate (HV off) 5. DCE RAM dump 6. Set flag 3 Day 13 Clear flag 3 (Real-time) -- After V27 1D for analysis. Flag 3 must be clear to continue science operations. Real Time Justification ----------------------- Real-time commanding is required to clear NSSC-1 COS event flag 3 at several points in this procedure. Calibration Justification ------------------------- Additional Comments ------------------- This proposal requires Special Commanding. A contingency Operations Request to place the FUV detector into its Inhibit Mode must be in place in case a significant anomaly occurs. ------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 7] Visit: 01 Visit Requirements: GYRO MODE 3GOBAD; PARALLEL On Hold Comments: Additional Comments: QE grid off, Turn-on HV. Special commanding will be used to execute the FUV Operate to HV On (0/0 or approximately ~ -2500V) reconfiguration and will stop there. Diagnostics are taken (DCE RAM dumps) after each transition. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR ELOPTNQF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVLOW; SEQ 1-2 NON-INT Comments: Turn on the FUV HV without the QE grid. Do not ramp up. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVLOW Comments: Copy and dump DCE RAM. From Jason McPhate (Berkeley FUV detector expert, who defined the FUV initial turn-on procedure): "[I'm after] the procedure to get a memory dump of the FUV HV and AUX power current monitors (HVIA, HVIB, AUXI). Each of these has a 1000 (possibly 1024) sample buffer that monitors the current at 1ms sampling (looping through, overwriting the data that is 1 second old), and a cumulative histogram of the current values (this would be a buffer of 256 values for each monitor)." This information is in a DCE RAM dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 8] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 9] Visit: 02 Visit Requirements: GYRO MODE 3GOBAD; AFTER 01 BY 1.1 H TO 10.0 H; PARALLEL On Hold Comments: Additional Comments: Following visit 01 by 1 hour, continue with the FUV ramp-up with the QE off to HVLow value (100/100). The HOME alignment is not needed and may be deleted via SQL. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 1035 S SAA CONTOUR 31; SPEC COM INSTR ELHOTHLF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVLOW; SEQ 1-3 NON-INT Comments: Ramp the FUV HV to HVLow. The commanding assumes the HV is already on. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVLOW Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT; G STIM-RATE=2000 QASISTATES COS FUV HVLOW HVLOW ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 10] Visit: 03 Visit Requirements: GYRO MODE 3GOBAD; AFTER 02 BY 1.5 H TO 10.0 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, return to Operate, and dump DCE memory. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW OPERATE; SEQ 1-2 NON-INT Comments: Turn off the FUV high voltage ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 11] Visit: 04 Visit Requirements: GYRO MODE 3GOBAD; AFTER 03 BY 1.1 H TO 10 H; PARALLEL On Hold Comments: Additional Comments: QE grid on, HV on Special commanding will be used to execute the FUV Operate to HV On (0/0 or approximately ~ -2500V) reconfiguration and will stop there. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SPEC COM INSTR ELOPTHOF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVLOW; SEQ 1-2 NON-INT Comments: Turn on the FUV HV, including the QE grid. Do not ramp up. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVLOW Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 12] Visit: 05 Visit Requirements: GYRO MODE 3GOBAD; AFTER 04 BY 1.1 H TO 10.0 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, return to Operate, dump DCE memory, and set flag 3. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW OPERATE; SEQ 1-3 NON-INT Comments: Turn off the FUV high voltage ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 13] Visit: 06 Visit Requirements: GYRO MODE 3GOBAD; AFTER 01 BY 1.0 D TO 2.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on (without the QE grid) and Ramp the FUV high voltage up to a specified value (well below HVNom). No SAA Passage between Visits 06 and 07. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 120.0 S SPEC COM INSTR ELFUVMEMMON; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVNOM; SEQ 1-3 NON-INT Comments: Start memory monitors and allow time to get initial readings. Monitor the HVNom segment A & B count levels and the time per HV step. These items will be patched throughout the remaining execution of this proposal. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR ELOPTNQF Comments: Turn on the HV without the QE grid. ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 1035 S SAA CONTOUR 31; SPEC COM INSTR ELHOTHLF Comments: Ramp the FUV HV to HVLow. The commanding assumes the HV is already on. ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 379 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; AFTER BY 4635 S; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM; QESIPARM ENDCTSA 154; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 151; SEQ 4-7 NON-INT Comments: Ramp the FUV HV to 154/151 counts (A/B). The AFTER BY enforces the 10.2 one hour warmup time for HVLOW. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 14] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 7 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 7 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 15] Visit: 07 Visit Requirements: GYRO MODE 3GOBAD; AFTER 06 BY 2.8 H TO 3.2 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 06 and 07. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: enforce the intent of the seq non-int across the obsets (qbs_obset..max_sep_dur) ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF Comments: Turn off the FUV high voltage ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 16] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 17] Visit: 08 Visit Requirements: GYRO MODE 3GOBAD; AFTER 04 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on and Ramp the FUV high voltage up to HVLow. The HOME alignment is not needed and may be deleted via SQL. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 1060 S SAA CONTOUR 31; SPEC COM INSTR RLOPTHLF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVLOW; SEQ 1-3 NON-INT ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVLOW Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT; G STIM-RATE=2000 QASISTATES COS FUV HVLOW HVLOW ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 18] Visit: 09 Visit Requirements: GYRO MODE 3GOBAD; AFTER 08 BY 1.6 H TO 10.0 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, return to Operate, dump DCE memory, and set flag 3. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW OPERATE; SEQ 1-3 NON-INT ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 19] Visit: 10 Visit Requirements: GYRO MODE 3GOBAD; AFTER 06 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on (without the QE grid) and Ramp the FUV high voltage up to a specified value (higher than v06, lower than HVNom). No SAA Passage between Visits 10 and 11. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR ELOPTNQF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVNOM; SEQ 1-2 NON-INT Comments: Turn on the HV without the QE grid. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 1035 S SAA CONTOUR 31; SPEC COM INSTR ELHOTHLF Comments: Ramp the FUV HV to HVLow. The commanding assumes the HV is already on. ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 397 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; AFTER BY 4635 S; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM; QESIPARM ENDCTSA 160; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 157; SEQ 3-6 NON-INT Comments: Ramp the FUV HV to 160/157 counts (A/B). The AFTER BY enforces the 10.2 one hour warmup time for HVLOW. ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) 12810( 8) - 14-May-2012 18:01:43 - [ 20] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 6 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 6 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 21] Visit: 11 Visit Requirements: GYRO MODE 3GOBAD; AFTER 10 BY 2.8 H TO 3.2 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 10 and 11. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 22] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 23] Visit: 12 Visit Requirements: GYRO MODE 3GOBAD; AFTER 08 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on and Ramp the FUV high voltage up to a specified value (well below HVNom). No SAA Passage between Visits 12 and 13. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 379 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVNOM; QESIPARM ENDCTSA 154; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 151; SEQ 1-4 NON-INT Comments: Ramp the FUV HV to 154/151 counts (A/B). ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 4 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 24] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ WAVE 4 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 25] Visit: 13 Visit Requirements: GYRO MODE 3GOBAD; AFTER 12 BY 1.5 H TO 2.1 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 12 and 13. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT; SEQ 1-6 G STIM-RATE=2000 NON-INT ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 26] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 27] Visit: 14 Visit Requirements: GYRO MODE 3GOBAD; AFTER 10 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on (without the QE grid) and Ramp the FUV high voltage up to a specified value (higher than v10, lower than HVNom). No SAA Passage between Visits 14 and 15. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR ELOPTNQF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVNOM; SEQ 1-2 NON-INT Comments: Turn on the HV without the QE grid. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 1035 S SAA CONTOUR 31; SPEC COM INSTR ELHOTHLF Comments: Ramp the FUV HV to HVLow. The commanding assumes the HV is already on. ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 415 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; AFTER BY 4635 S; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM; QESIPARM ENDCTSA 166; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 163; SEQ 3-6 NON-INT Comments: Ramp the FUV HV to 166/163 counts (A/B). The AFTER BY enforces the 10.2 one hour warmup time for HVLOW. ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) 12810( 8) - 14-May-2012 18:01:43 - [ 28] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 6 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 6 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 29] Visit: 15 Visit Requirements: GYRO MODE 3GOBAD; AFTER 14 BY 2.8 H TO 3.4 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 14 and 15. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT; SEQ 1-6 G STIM-RATE=2000 NON-INT ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 30] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 31] Visit: 16 Visit Requirements: GYRO MODE 3GOBAD; AFTER 12 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on and Ramp the FUV high voltage up to a specified value (higher than v12, lower than HVNom). No SAA Passage between Visits 16 and 17. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 397 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVNOM; QESIPARM ENDCTSA 160; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 157; SEQ 1-4 NON-INT Comments: Ramp the FUV HV to 160/157 counts (A/B). ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 4 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 32] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ WAVE 4 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 33] Visit: 17 Visit Requirements: GYRO MODE 3GOBAD; AFTER 16 BY 1.5 H TO 2.1 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 16 and 17. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 34] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 35] Visit: 18 Visit Requirements: GYRO MODE 3GOBAD; AFTER 14 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on (without the QE grid) and Ramp the FUV high voltage up to a specified value (higher than v14, lower than HVNom). No SAA Passage between Visits 18 and 19. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR ELOPTNQF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVNOM; SEQ 1-2 NON-INT Comments: Turn on the HV without the QE grid. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 1035 S SAA CONTOUR 31; SPEC COM INSTR ELHOTHLF Comments: Ramp the FUV HV to HVLow. The commanding assumes the HV is already on. ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 433 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; AFTER BY 4635 S; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM; QESIPARM ENDCTSA 172; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 169; SEQ 3-6 NON-INT Comments: Ramp the FUV HV to 172/169 counts (A/B). The AFTER BY enforces the 10.2 one hour warmup time for HVLOW. ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) 12810( 8) - 14-May-2012 18:01:43 - [ 36] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 6 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 6 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 37] Visit: 19 Visit Requirements: GYRO MODE 3GOBAD; AFTER 18 BY 2.8 H TO 3.4 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 18 and 19. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int between the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 38] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 39] Visit: 20 Visit Requirements: GYRO MODE 3GOBAD; AFTER 16 BY 2 D TO 4 D; PARALLEL On Hold Comments: Additional Comments: Turn on and Ramp the FUV high voltage up to a specified value (higher than v16, lower than HVNom). No SAA Passage between Visits 20 and 21. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 415 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVNOM; QESIPARM ENDCTSA 166; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 163; SEQ 1-4 NON-INT Comments: Ramp the FUV HV to 166/163 counts (A/B). ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OPERATE OPERATE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 4 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 40] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ WAVE 4 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 41] Visit: 21 Visit Requirements: GYRO MODE 3GOBAD; AFTER 20 BY 1.6 H TO 2.2 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 20 and 21. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 42] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 43] Visit: 22 Visit Requirements: GYRO MODE 3GOBAD; AFTER 18 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on (without the QE grid) and Ramp the FUV high voltage up to HVNom. No SAA Passage between Visits 22 and 23. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR ELOPTNQF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE HVNOM; SEQ 1-2 NON-INT Comments: Turn on the HV without the QE grid. ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 1035 S SAA CONTOUR 31; SPEC COM INSTR ELHOTHLF Comments: Ramp the FUV HV to HVLow. The commanding assumes the HV is already on. ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 280 S SAA CONTOUR 31; SPEC COM INSTR RLHLTHNF; AFTER BY 4635 S; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM; SEQ 3-6 NON-INT Comments: Ramp the FUV HV to 178/175 counts (A/B, the nominal HVNom values). The AFTER BY enforces the 10.2 one hour warmup time for HVLOW. ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 12810( 8) - 14-May-2012 18:01:43 - [ 44] Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------------ 6 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 6 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 45] Visit: 23 Visit Requirements: GYRO MODE 3GOBAD; AFTER 22 BY 2.8 H TO 3.4 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 22 and 23. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 46] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 47] Visit: 24 Visit Requirements: GYRO MODE 3GOBAD; AFTER 20 BY 2.0 D TO 4.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on and Ramp the FUV high voltage up to a specified value (higher than v20, lower than HVNom). No SAA Passage between Visits 24 and 25. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 433 S SAA CONTOUR 31; SPEC COM INSTR ELHLTHVF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVNOM; QESIPARM ENDCTSA 172; QESIPARM SECPERCT 3; QESIPARM ENDCTSB 169; SEQ 1-4 NON-INT Comments: Ramp the FUV HV to 172/169 counts (A/B). ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 4 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 48] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ WAVE 4 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 49] Visit: 25 Visit Requirements: GYRO MODE 3GOBAD; AFTER 24 BY 1.5 H TO 2.1 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 24 and 25. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce the seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 50] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 51] Visit: 26 Visit Requirements: GYRO MODE 3GOBAD; AFTER 24 BY 1.0 D TO 2.0 D; PARALLEL On Hold Comments: Additional Comments: Turn on and Ramp the FUV high voltage up to HVNom. No SAA Passage between Visits 26 and 27. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK S/C DATA NONE 1 280 S SAA CONTOUR 31; SPEC COM INSTR RLHLTHNF; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVLOW HVNOM; SEQ 1-4 NON-INT Comments: Ramp the FUV HV to 178/175 counts (A/B, the nominal HVNom values). ------------------------------------------------------------------------------------------------------------------------------------ 2 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM HVNOM Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S NEW ALIGNMENT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 4 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 S/C DATA NONE none none none none 1 N/A DARK 2 S/C DATA NONE none none none none 1 N/A DARK 3 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 4 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G 12810( 8) - 14-May-2012 18:01:43 - [ 52] Visit: 27 Visit Requirements: GYRO MODE 3GOBAD; AFTER 26 BY 1.5 H TO 2.1 H; PARALLEL On Hold Comments: Additional Comments: Wait at least 1 hour, take a DARK and a WAVE exposure, return to Operate, dump DCE memory, and set flag 3. No SAA Passage between Visits 26 and 27. Exposures ------------------------------------------------------------------------------------------------------------------------------------ Exp | Target | Instr | Oper. | Aper |Spectral|Central| Optional |Num| Time | Special Num | Name | Config | Mode | or FOV |Element |Waveln.| Parameters |Exp| | Requirements ------------------------------------------------------------------------------------------------------------------------------------ 1 DARK COS/FUV TIME-TA DEF DEF BUFFER-TIME=300, 1 300.0 S SEQ 1-6 NON-INT G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 2 WAVE COS/FUV TIME-TA WCA G160M 1600 CURRENT=MEDIUM, FP-POS=3, 1 60 S G STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ 3 DARK S/C DATA NONE 1 35 S SAA CONTOUR 31; SPEC COM INSTR RLHNTHLF; NEW OBSET; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV HVNOM OPERATE Comments: SQL: Enforce seq non-int across the obsets ------------------------------------------------------------------------------------------------------------------------------------ 4 DARK S/C DATA NONE 1 50 S SAA CONTOUR 31; SPEC COM INSTR RLHLTOPF ------------------------------------------------------------------------------------------------------------------------------------ 5 DARK S/C DATA NONE 1 60.0 S SAA CONTOUR 31; SPEC COM INSTR ELCOPYDCE; NEW ALIGNMENT; QASISTATES COS SI OBSERVE OBSERVE; QASISTATES COS FUV OPERATE OPERATE Comments: DCE RAM copy and dump. See Visit 1, Exposure 2 for a complete description of the dump. SQL: setup readout entry for the DCE dump (qalignment, qexposure, qreadout), tag as COS (si_used and si_intrlv) ------------------------------------------------------------------------------------------------------------------------------------ 6 DARK S/C DATA NONE 1 1.0 S SPEC COM INSTR ELFLAG3; NEW ALIGNMENT Comments: Set NSSC-1 COS event flag 3. This will prevent subsequent FUV commanding unless it is cleared first. ------------------------------------------------------------------------------------------------------------------------------------ 12810( 8) - 14-May-2012 18:01:43 - [ 53] Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ Sub Exposures ------------------------------------------------------------------------------------------------------------------------------------ Target | Exp |Instr | Oper. | Aper |Spectral|Cent.|Primary |Secondary |Iteration |CR-SPLIT |Orbit |Duration Name | Num |Config | Mode | or FOV |Element |Wave.|Pattern Pos |Pattern Pos |Num |Num |Number | ------------------------------------------------------------------------------------------------------------------------------------ DARK 1 COS/FUV TIME-TA DEF DEF none none none none 1 N/A G WAVE 2 COS/FUV TIME-TA WCA G160M 1600 none none none none 1 N/A G DARK 3 S/C DATA NONE none none none none 1 N/A DARK 4 S/C DATA NONE none none none none 1 N/A DARK 5 S/C DATA NONE none none none none 1 N/A DARK 6 S/C DATA NONE none none none none 1 N/A 12810( 8) - 14-May-2012 18:01:43 - [ 54] Summary Form for Proposal 12810 Item Used in this proposal ------------------------------------------------------------------------------------------------------------------------------------ Apertures DEF, NONE, WCA ------------------------------------------------------------------------------------------------------------------------------------ Configurations COS/FUV, S/C ------------------------------------------------------------------------------------------------------------------------------------ Opmodes DATA, TIME-TAG ------------------------------------------------------------------------------------------------------------------------------------ Optional Parameters BUFFER-TIME=300, CURRENT=MEDIUM, FP-POS=3, STIM-RATE=2000 ------------------------------------------------------------------------------------------------------------------------------------ Special Requirements AFTER 01 BY 1.0 D TO 2.0 D, AFTER 01 BY 1.1 H TO 10.0 H, AFTER 02 BY 1.5 H TO 10.0 H, AFTER 03 BY 1.1 H TO 10 H, AFTER 04 BY 1.1 H TO 10.0 H, AFTER 04 BY 2.0 D TO 4.0 D, AFTER 06 BY 2.0 D TO 4.0 D, AFTER 06 BY 2.8 H TO 3.2 H, AFTER 08 BY 1.6 H TO 10.0 H, AFTER 08 BY 2.0 D TO 4.0 D, AFTER 10 BY 2.0 D TO 4.0 D, AFTER 10 BY 2.8 H TO 3.2 H, AFTER 12 BY 1.5 H TO 2.1 H, AFTER 12 BY 2.0 D TO 4.0 D, AFTER 14 BY 2.0 D TO 4.0 D, AFTER 14 BY 2.8 H TO 3.4 H, AFTER 16 BY 1.5 H TO 2.1 H, AFTER 16 BY 2 D TO 4 D, AFTER 18 BY 2.0 D TO 4.0 D, AFTER 18 BY 2.8 H TO 3.4 H, AFTER 20 BY 1.6 H TO 2.2 H, AFTER 20 BY 2.0 D TO 4.0 D, AFTER 22 BY 2.8 H TO 3.4 H, AFTER 24 BY 1.0 D TO 2.0 D, AFTER 24 BY 1.5 H TO 2.1 H, AFTER 26 BY 1.5 H TO 2.1 H, AFTER BY 4635 S, GYRO MODE 3GOBAD, NEW ALIGNMENT, NEW OBSET, PARALLEL, QASISTATES COS FUV HVLOW HVLOW, QASISTATES COS FUV HVLOW HVNOM, QASISTATES COS FUV HVLOW OPERATE, QASISTATES COS FUV HVNOM HVNOM, QASISTATES COS FUV HVNOM OPERATE, QASISTATES COS FUV OPERATE HVLOW, QASISTATES COS FUV OPERATE HVNOM, QASISTATES COS FUV OPERATE OPERATE, QASISTATES COS SI OBSERVE OBSERVE, QASISTATES COS SI OPERATE OPERATE, QESIPARM ENDCTSA 154, QESIPARM ENDCTSA 160, QESIPARM ENDCTSA 166, QESIPARM ENDCTSA 172, QESIPARM ENDCTSB 151, QESIPARM ENDCTSB 157, QESIPARM ENDCTSB 163, QESIPARM ENDCTSB 169, QESIPARM SECPERCT 3, SAA CONTOUR 31, SEQ 1-2 NON-INT, SEQ 1-3 NON-INT, SEQ 1-4 NON-INT, SEQ 1-6 NON-INT, SEQ 3-6 NON-INT, SEQ 4-7 NON-INT, SPEC COM INSTR ELCOPYDCE, SPEC COM INSTR ELFLAG3, SPEC COM INSTR ELFUVMEMMON, SPEC COM INSTR ELHLTHVF, SPEC COM INSTR ELHOTHLF, SPEC COM INSTR ELOPTHOF, SPEC COM INSTR ELOPTNQF, SPEC COM INSTR RLHLTHNF, SPEC COM INSTR RLHLTOPF, SPEC COM INSTR RLHNTHLF, SPEC COM INSTR RLOPTHLF ------------------------------------------------------------------------------------------------------------------------------------ Spectral Elements DEF, G160M ------------------------------------------------------------------------------------------------------------------------------------ Target Names DARK, WAVE ------------------------------------------------------------------------------------------------------------------------------------